Cybersecurity

NIST SP 800-82 Rev. 3 (Low OT Overlay)

NIST SP 800-82 Rev. 3 Low OT framework badge
Summarize with
ClaudeChatGPTPerplexityGoogle AI Mode
In this article
At a Glance
NIST SP 800-82 Rev. 3, Guide to Operational Technology (OT) Security: OT Overlay, Low-Impact Baseline
  • Classification
    Category
    Cybersecurity
    Domain
    Cybersecurity
    Framework Family
    NIST Special Publications
  • Regulatory Context
    Type
    Guidance
    Legal Instrument
    Guideline
    Sector
    Cross-Sector
    Industry
    Cross-Industry
  • Region / Publisher
    Region
    North America
    Region Detail
    United States
    Publisher
    National Institute of Standards and Technology (NIST)
  • Versioning
    Version
    Revision 3 OT overlay (September 28, 2023; Revision 4 initial public draft September 2026)
    Effective Date
    September 28, 2023
    Issue Date
    September 28, 2023
  • Adoption
    Adoption Model
    Voluntary
    Implementation Complexity
    Medium
  • Official Reference
License Information

License included / downloadable: Yes

NIST SP 800-82 Rev. 3, including Appendix F and Table 22, is available free of charge from NIST, and the Low baseline structure is included with the platform.

Framework text is licensed by its publisher and is included only where stated above.

Official Resources
NIST SP 800-82 Revision 3 - Guide to OT Security
Provides guidance on securing operational technology environments with tailored security controls.
NIST Cybersecurity Framework
Describes common policies to improve cybersecurity risk management.
NIST SP 800-53 Control Catalog
Defines the security and privacy controls for federal information systems that SP 800-161 draws its C-SCRM controls from.
NIST Risk Management Framework Overview
Outlines the integration of security and privacy into the system development life cycle.
Key takeaways
  • The NIST SP 800-82 Rev. 3 OT overlay Low baseline is the control set for OT systems rated low on all three FIPS 199 objectives.
  • NIST published Revision 3 on September 28, 2023, superseding Revision 2 of June 3, 2015.
  • The overlay is a partial tailoring of SP 800-53 Rev. 5 controls for OT, applicable to all OT systems in all industrial sectors.
  • It was tailored for the increased need for availability, safety, and environmental considerations in OT, including safe mode and fail-safe procedures.
  • A Revision 4 initial public draft is open for comment until November 30, 2026; Revision 3 stays in force until it is final.

Overview

The low-impact baseline of the OT overlay in NIST SP 800-82 Rev. 3, Guide to Operational Technology (OT) Security, is the subject of this page: the Low column of Table 22 in Appendix F, the starting control set for an OT system categorized low under FIPS 199. A low-impact system is one in which all three security objectives, confidentiality, integrity and availability, are low (Section 2.2 of NIST SP 800-53B). NIST published Revision 3 as final on September 28, 2023, superseding Revision 2 of June 3, 2015; a Revision 4 draft is open for comment until November 30, 2026, and Revision 3 stays in force until it is final. The moderate and high baselines have their own pages.

The guide defines OT as programmable systems and devices that interact with the physical environment, or manage devices that do, such as industrial control, building automation, physical access control and environment monitoring systems (abstract). Its Note to Readers records the expansion in scope from industrial control systems to OT, new tailoring guidance for SP 800-53 Rev. 5 and an OT overlay with baselines for low-, moderate- and high-impact OT systems. Appendix F describes that overlay as a partial tailoring of the SP 800-53 Rev. 5 controls and baselines with supplementary OT guidance, applicable to all OT systems in all industrial sectors, citable as the NIST SP 800-82 Rev 3 OT Overlay and developed under FISMA 2014, PPD-21 and Executive Order 13636.

For a low-impact OT system the overlay adds items that the SP 800-53B low baseline does not contain: CP-12 Safe Mode, SI-17 Fail-Safe Procedures, MA-7 Field Maintenance, AU-4(1) Transfer to Alternate Storage, AC-17(9) Disconnect or Disable Access, SC-7(28) Connections to Public Networks and SC-7(29) Separate Subnets to Isolate Functions. An organization categorizes the system under Section 4 and Table 7, takes the Low column of Table 22 as its starting set, reads the OT Discussion for each control in F.7, applies the F.4 rules for compensating controls under PL-11 and the F.5 note on serial and other non-routable protocols, and documents the result in the OT security plan.

Why does it matter?

A low FIPS 199 rating keeps the control set small, but it does not remove what makes OT different: F.4 says the SP 800-53B baselines were tailored for the increased need for availability, safety and environmental or operating-environment considerations in OT, and Table 1 of the guide sets out the IT-to-OT differences behind that. Without the overlay, a low-impact building automation or monitoring system would take the SP 800-53B low baseline as written, with no safe mode, no fail-safe procedure and no field maintenance control. The Low baseline of the overlay supplies those few additions, keeps everything else at the low level, and gives each control an OT Discussion so the organization can tailor further with a written rationale.

Key benefits include:

  • The smallest OT starting set

The Low column of Table 22 carries base controls where the moderate and high columns carry enhancements, for example AC-2, AU-6, CP-2 and CP-10 without enhancements, and leaves out AC-6, AC-11, AC-12, CP-6, CP-7 and CP-8 altogether.

  • OT additions at every level

CP-12 Safe Mode, SI-17 Fail-Safe Procedures, MA-7 Field Maintenance and AU-4(1) appear in all three columns of Table 22 and in none of the SP 800-53B baselines, so a low system gains them too.

  • Low-specific remote access and boundary entries

AC-17(9) is the only remote access enhancement in the Low column, and SC-7(28) and SC-7(29) are the boundary enhancements the overlay adds for low- and moderate-impact OT systems.

  • Compensating controls that are not waivers

F.4 states that compensating controls implemented under PL-11 are alternative safeguards, not exceptions or waivers, documented with their equivalence and residual risk in the security plan.

  • Serial and non-routable protocols covered

F.5 notes that controls assuming network addressing need tailoring for devices that communicate over RS-232 and similar interfaces, common in OT equipment.

How does it work?

Categorization comes first. Section 4 applies the Risk Management Framework to OT, and Table 7 notes that OT and IT systems may have different categorization criteria and that the system process should be considered. FIPS 199 rates confidentiality, integrity and availability separately and the high water mark sets the system level; only a system rated low on all three selects the Low baseline. Table 22 in F.3 then lists every SP 800-53 Rev. 5 control and enhancement allocated to the Low, Moderate and High baselines with three conventions: bold for rows with OT discussion, underline for a control added beyond SP 800-53B, and strikethrough for a removal, illustrated with AU-4(1), which was added to all three baselines with OT discussion.

The Low column is deliberately short. Account Management stops at AC-2 while the moderate column carries AC-2(1) to (5) and (13); Remote Access carries AC-17(9) alone; Wireless Access is AC-18 without enhancements; Audit Record Review is AU-6; Continuous Monitoring is CA-7(4); Contingency Plan is CP-2 and System Recovery is CP-10, both without enhancements; Identification and Authentication keeps IA-2(1), (2), (8) and (12) and IA-5(1); Media Sanitization is MP-6; Boundary Protection carries SC-7(28) and (29); and Supply Chain Risk Management carries SR-2(1), SR-5, SR-11(1) and (2) and SR-12. CP-12 Safe Mode, SI-17 Fail-Safe Procedures, MA-7 Field Maintenance, PL-10 Baseline Selection and PL-11 Baseline Tailoring sit in every column.

Tailoring follows F.4. The overlay is a starting point that organizations tailor further; where the OT cannot support a control or enhancement, or implementing it would harm performance, safety or reliability, a compensating control may be used, including a nonautomated procedure. The organization documents why the baseline control could not be implemented, how the compensating control provides equivalent capability and the residual risk it accepts, and records the decision in the security plan for the OT; an assignment may be tailored out by assigning the value none. F.7 then gives the detailed specifications family by family, from F.7.1 Access Control to F.7.19 Supply Chain Risk Management, each control with its OT Discussion in the Fig. 22 format.

Key Elements

  • Low column of Table 22 (F.3)

The controls and enhancements allocated to low-impact OT systems, read against the bold, underline and strikethrough conventions that show OT discussion, additions and removals relative to SP 800-53B.

  • Additions in all three baselines

CP-12 Safe Mode, SI-17 Fail-Safe Procedures, MA-7 Field Maintenance and AU-4(1), none of which the SP 800-53B low, moderate or high baselines contain.

  • Low-specific entries

AC-17(9) Disconnect or Disable Access as the sole remote access enhancement at low, and SC-7(28) Connections to Public Networks and SC-7(29) Separate Subnets to Isolate Functions, added for low- and moderate-impact systems.

  • Categorization for OT (Section 4, Table 7)

FIPS 199 with the high water mark, with the note that OT and IT may use different categorization criteria and that the system process should be considered.

  • Tailoring and compensating controls (F.4)

PL-11 compensating controls as alternative safeguards rather than waivers; three documented points; decisions recorded in the OT security plan; assignments tailored out as none.

  • OT communication protocols (F.5)

Controls that assume network routing or addressing need tailoring for non-routable interfaces such as RS-232 serial links.

  • Detailed specifications and exclusions (F.7, F.2)

Per-family control tables with OT Discussion from F.7.1 to F.7.19 in the Fig. 22 format; controls that appear only in the privacy baseline are removed from the overlay.

What does it cover?

F.2 says the overlay was prepared for use by federal agencies and may be used by non-governmental organizations on a voluntary basis, and Appendix F says it is intended for all OT systems in all industrial sectors. Section 2 describes the OT the guide covers: SCADA, distributed control systems, programmable logic controllers, building automation, physical access control, safety instrumented systems and the industrial internet of things. This page concerns only the Low baseline, for OT systems rated low on all three FIPS 199 objectives; privacy-only controls are excluded (F.2), and the guidelines do not apply to national security systems without the approval of the officials with policy authority over them.

What are its objectives?

Appendix F sets out what the overlay is for, and the Low baseline carries those purposes for low-impact OT:

Tailor the SP 800-53 Rev. 5 controls and the SP 800-53B low baseline for OT, with supplementary guidance specific to OT (Appendix F).

Account for availability, safety and environmental or operating-environment considerations that distinguish OT from IT, even at the low impact level (F.4).

Add the controls OT needs regardless of impact level, such as safe mode, fail-safe procedures and field maintenance (Table 22).

Give organizations a starting point they can tailor further to the variability of OT architectures, protocols and technologies (F.4, F.5).

Treat any compensating control for a low-impact OT system as a documented risk decision: F.4 asks for the reason the baseline control could not be implemented, how the alternative gives equivalent protection and the residual risk accepted, all recorded in the security plan.

Framework in Context

The Low baseline draws its controls from the NIST SP 800-53 Rev. 5 catalog and its structure from NIST SP 800-53B, whose Appendix C defines overlays and whose low baseline is the starting point. F.4 refers to Control Tailoring in Section 3.3 of NIST SP 800-37 Rev. 2, Section 4 applies the RMF steps to OT in Tables 6 to 12, and Section 6 relates OT practice to the Cybersecurity Framework. The Moderate and High OT baselines add enhancements on top of this one, for example AC-17(10), CP-10(6) and SR-5(1) at moderate. The CSRC record lists a Potential updates spreadsheet of July 10, 2024 and the Revision 4 initial public draft.

Common Framework Mappings

The Low OT baseline is commonly mapped to the control catalogs and sector standards that OT owners report against, so one tailored baseline and its evidence can serve several programs.

Mapped frameworks include:

CIS Controls v8.1

CSA CCM v4

IEC 62443

ISO 27001:2022

ISO 27002:2022

NERC CIP

NIST CSF 2.0

NIST 800-53 Rev.5

SOC 2

Cyber Essentials

SMARTSUITE

How SmartSuite Supports NIST 800-82 Rev. 3 (Low OT Overlay)

SmartSuite provides the system for managing controls, evidence, mappings, assessments, and reporting.

Use Cyber & IT Risk to hold the Low column of Table 22 as a control register for each low-impact OT system, Compliance Management to keep the F.4 compensating-control record and the security plan evidence beside each control, Operational Resilience & Business Continuity for the CP-12 safe mode and SI-17 fail-safe procedures the overlay adds, and Third Party Risk Management for the SR-2(1), SR-11 and SR-12 supply chain controls the low column carries.

Low Baseline Register (Table 22)

Load the Low column as records in Cyber & IT Risk, one per control and enhancement, with the OT Discussion reference, an owner and the implementation status for each OT system.

Categorization Record (Section 4, Table 7)

Document the FIPS 199 rating of each objective, the system process considered and the finding that all three are low, as the evidence that the Low baseline applies.

Safe Mode and Fail-Safe Procedures (CP-12, SI-17)

Keep the defined safe-mode conditions and the written fail-safe procedures in Operational Resilience & Business Continuity, with the MA-7 field maintenance arrangements and review dates.

Compensating-Control Record (F.4, PL-11)

Capture for each compensating control why the baseline control could not be implemented, how the alternative gives equivalent capability and the accepted residual risk, with the security plan reference.

Protocol Tailoring Record (F.5)

List the devices that communicate over RS-232 and other non-routable interfaces and the tailoring applied to the controls that assume network addressing, such as the SC-7 boundary enhancements.

Supply Chain Controls at Low

Track SR-2(1), SR-5, SR-11(1) and (2) and SR-12 in Third Party Risk Management by supplier and OT component, linked to the assessments and evidence that support them.

Related frameworks

CIS Controls v8.1

CIS Controls v8.1 is a prioritized set of 18 Controls and 153 Safeguards, in three Implementation Groups, with a new Govern function.

IEC 62443-4-2

IEC 62443-4-2:2019 sets technical security requirements for IACS components, with seven foundational requirements and security levels 1 to 4.

ISO 27001:2022

ISO/IEC 27001:2022 specifies requirements for an information security management system: Clauses 4 to 10, risk treatment, the Statement of Applicability and 93 Annex A controls.

NIST CSF 2.0

NIST CSF 2.0 (CSWP 29, February 26, 2024) is the voluntary cybersecurity framework with six Functions including Govern, 22 Categories, 106 Subcategories, Profiles and Tiers.

NIST 800-53 Rev.5

NIST SP 800-53 Rev. 5 is the NIST catalog of security and privacy controls in 20 families, mandatory for federal systems under OMB A-130 and FISMA; Release 5.2.0 issued August 27, 2025.

NIST 800-82 Rev.3 Moderate OT

Moderate baseline of the NIST SP 800-82 Rev. 3 OT overlay: SP 800-53B moderate controls tailored for moderate-impact OT systems, with the Appendix F additions, removals and tailoring rules.

SOC 2

SOC 2 is the AICPA examination, under AT-C 105 and 205, of a service organization's controls against the 2017 Trust Services Criteria, issued as a type 1 or type 2 attestation report.

FAQ

Frequently Asked Questions For NIST SP 800-82 Revision 3 (Low OT Overlay)

OT systems categorized low impact under FIPS 199, which Section 2.2 of SP 800-53B defines as systems in which all three security objectives, confidentiality, integrity and availability, are low. Section 4 of SP 800-82 Rev. 3 applies the RMF to OT, and Table 7 notes that OT and IT may use different categorization criteria and that the system process should be considered; a system with any moderate or high objective uses the Moderate or High baseline instead.

Table 22 adds CP-12 Safe Mode, SI-17 Fail-Safe Procedures, MA-7 Field Maintenance and AU-4(1) to all three OT baselines, none of which appear in the SP 800-53B baselines, and the Low column also carries AC-17(9) and the boundary protection enhancements SC-7(28) and SC-7(29), which the SP 800-53B low baseline does not contain. F.3 uses AU-4(1) as its worked example of an added control with OT discussion.

F.2 says the overlay was prepared for use by federal agencies and may be used by non-governmental organizations on a voluntary basis. NIST developed it under FISMA 2014, PPD-21 and Executive Order 13636, and it is registered in the CSRC overlay repository; it does not create a certification, and the guidelines do not apply to national security systems without the approval of the officials with policy authority over them.

F.4 allows a compensating control when the OT cannot support a baseline control or enhancement, or when implementing it would harm performance, safety or reliability; a nonautomated procedure may stand in for an automated mechanism. Compensating controls under PL-11 are not exceptions or waivers. The organization documents why the baseline control could not be implemented, how the compensating control provides equivalent security capability and the accepted residual risk, and records the decision in the security plan for the OT.

Yes. The CSRC record shows Revision 3 as final on September 28, 2023, superseding Revision 2 of June 3, 2015, and its planning note of September 21, 2026 points to the initial public draft of Revision 4 with public comments due November 30, 2026. A draft does not supersede the final publication, so the Rev. 3 overlay and its Low baseline remain the current reference until Revision 4 is published as final; NIST also lists a Potential updates spreadsheet dated July 10, 2024.

Put this framework to work in SmartSuite

Manage controls, risks, evidence, and audits in one platform designed for modern governance, risk, and compliance.